SilverStone GD04B Guia de Instalação

GD04

9910The tray areas around themotherboard have many small pass-through holes that can be used with included wire tie, please refer to the illustration

101112Now carefully count and separate the required power cables for your hard drive, optical drive, and graphics card. Place the needed cables out o

111314Install and secure any 3.5” or 2.5” hard drive into the hard drive bracket with screws. The purpose of using screws for hard drive installation

1215There are pass-through holes next to the hard drive bracket for tidying hard drive or power cables using wire ties. There is also a rubber partit

131617Install and secure the optical drive onto the optical drive bracketВставьте оптический привод в кронштейн и закрепите его.Installieren und fixie

14lnstallation Guide1819There are pass-through holes next to the optical drive bracket for tidying hard drive or power cables using wire ties.Рядом с

152021Test mount the optical drive bracket assembly back into the case and align the optical drive button to the button on the case, if necessary, loo

1622lnstallation GuideAdjust the position of the optical drive bracket to align the drive cover parallel with the case front panel, make sure the opti

172324Place the top cover back onto the case and secure with three screws.Установите на место верхнюю крышку корпуса и закрепите ее тремя шурупами.Set

18Power switch and reset switch installation guide:Please refer to the motherboard manuals for the motherboard’s “Front Panel Connector” or “System Pa

1Installation and system optimization guide:The following manual and guides were carefully prepared by the SilverStone engineering team to help you ma

19 Front I/O connector guideBelow are the front I/O connectors pin definition, please also check your motherboard manual to cross reference with mothe

20Component size limitationsThe GD04 was designed to be as small as possible while maximizing interior space usage, please refer to the following guid

21 Power supply length limitationThe allowable power supply length is determined by the left intake fan size. Please refer to the table below as a gu

22಴Ў*'೼ᴎㆅݙֱ᳝ᣕⳌᔧⱘᭈ㒓ぎ䯈Ϣ⧚㒓㾘ߦDŽेՓՓ⫼໻䞣ⱘ໮佔㒓ᴤгϡᕅડࠄᅝ㺙ᗻϢ⇨⌕DŽ៥Ӏᓎ䆂ৃҹ䞛⫼23(67()67)671)ĂㄝⳈߎ㒓ⱘ⬉⑤կᑨ఼DŽ៥Ӏᔎ⚜᥼㤤23(಴Ў23(ⱘ(363LQ㒓䭓䎇໳ৃҹ

23Graphics card/expansion card length limitationGD04 can support 10.5”(267mm) consumer level graphics cardsOptical drive cover limitationsIn keeping t

24Recommended cooling device setup and selectionWhen choosing a graphics card, we recommend models that have fan blowing exhaust air to the rear slot,

Upgrading case fanSilverStone already includes three 120mm low noise fans in the GD04. The fans are selected to maintain class-leading cooling perfor

26Cleaning of fan filters on a regular basis is highly recommendedPicture: An example of a GPU cooler that is filled with dust and has lost most of it

271.Refer to the case installation guide to properly remove the drive bracket, then loosen the fan screws to remove the fans. 2.Loosen the screws hold

28Dual purpose spaceABA.Installation of a 3.5” hard driveB.Installation of a slot device or short expansion card such as extra motherboard I/O, fan co

GD04The ultimate HTPC chassis for true living room integration28.0mm aluminum front panel, 0.8mm SECC bodyMicro ATXRight SideLeft SideRearSST-GD04B(Bl

29Expansion card removal guideIf the rear hard drive’s cables are blocking the left expansion card, please first unplug the hard drive cables then pro

30If the expansion card on the right side is blocked by the card to the left, please first remove the card on the left side to allow the card on the r

NO: G11210490August, 2009

35.25”BAY12025 FAN x 2MICRO ATX M/B(OPTION)8025 FAN x 2(OPTION)TOP COVERRESET BUTTONPOWER BUTTONUSB2.0 x 2 +SPK+MICPS2 PSU(OPTION)12025 FAN x 13.5” x

412Unscrew the three screws from the rear of the chassis then remove the top cover.Открутите три шурупа с задней части корпуса, затем снимите верхнюю

534Unscrew two screws from the centerbrace to remove it.Открутите два шурупа на центральной скобе и выньте ее.Открутите шурупы на кронштейне жесткого

65Adhere the included power supply feet to the end of the power supply for supportПрикрепите прилагаемые опорные ножки к блоку питания.Bringen Sie die

76Install power supply into the case, if the power supply is a little too deep, please install at an angle as shown in illustration A and B.(If the po

878Insert the I/O shield included with your motherboard, then install the motherboard into the caseУстановите заглушку для разъёмов задней панели мате